FREE SHIPPING AUSTRALIA WIDE!

Topargee Flush Mount (H2F – FM) – Water Tank Gauge, RV, Motorhome, Boat, Caravan, 4×4

Topargee Flush Mount (H2F – FM) – Water Tank Gauge, RV, Motorhome, Boat, Caravan, 4×4

$129.00

New Flush Mount Model Larger Backlit Screen

Breakthrough Design for the RV and Marine Industries
*Takes all the guess work out of your water supply.
*Displays number of litres left in your water tank.
*Counts down litre by litre from a preset amount.
*Stop wasting fuel by filling up unnecessarily.
*Know how much is used for washing, showers etc.
*Know your daily water usage in litres
*Essential for bush/ free camping.
*Fitted in water line, nothing is fitted to water tanks.
*One unit can be used for any number or size tanks.
​*Displays in gallons or litres.
*It can be used in conjunction with your current system to accurately know your capacity and usage.
N.B. Does not include hose connectors.
Our new RV senders and electronics are compatible with all commonly available RV and marine water pumps and will even work with gravity fed systems.

We now have two exclusive RV & marine models, one suited more to the DIY aftermarket H2F-SM and our new flush mount H2F-FM (this page) designed to provide a superior appearance to more closely match the other displays in new RVs and boats.

If extra length of lead is required, please purchase the “3 Pin Sender Extension Lead”, as we have found other leads extensions cause inaccuracy in the meter readings.

3 Pin Sender Extension Lead available in either 1.4m ($7.95) or 3m ($14.95).

**If required, multiple leads can be joined to make up the length**

***************************************************************

Fitting recessed display 
The LCD Polarised Display on this new model is designed to be only visible when viewed from horizontal and below .
When viewed from this angle the display is extremely clear.
Using the display as a template mark out hole and cut to suit.
Fix in position with bolts provided or suitable screws..

Connecting Sender Unit
The display comes pre-wired with an approximately 1.4m sender cable. Extra 1.4m extension leads are available for the three pin plugs, up to 6 leads may be joined to make 9.8m in total length.  Leads cannot be cut and joined, doing so will void warranty, No Exceptions.
The thread specifications of the sender unit are 1/2″ BSP male.   Make sure the sender is fitted with the water flow in the direction of the arrow.
You will need to purchase two 1/2″ BSP female connectors to the size hose you have, usually 1/2″ or 3/4″ and two clamps.  “John Guest quick connections” also have fittings to suit their hose and the 1/2″ BSP sender unit.

Connection to 12 Volt DC
Simply cut off the two pin 12v plug to the required length and connect the black wire to the negative terminal and the red wire to the positive power source.  All settings and amounts will be memorised if power is disconnected.

Programming Monitoring Capacity
Press “DISPLAY” button to turn display on, then press the “PROG” button, “ProG” will blink on the LCD display. Press and release “RESET” button to choose the value of the right digit.  Once the value has been chosen, press “PROG” button to save the value, it will then go to the next digit.  Repeat the above procedure to program the values for the five digits from right to left.
The maximum monitoring capacity is 99,999 litres.  The first time the meter is used fill the water tank and then use normally until empty.  Then note how many usable litres the tank holds and reset the meter accordingly.
*If there is no input for one minute during the programming procedure, the programming procedure will be terminated and goes back to the original status.

Operating
The TOPARGEE H2Flow will automatically turn on and display the litres remaining when there is water flowing through the sensor e.g. a tap is turned on.  It will automatically turn off 10 seconds after there is no water flowing.
To manually check remaining litres, press and release “Display” button and remaining litres will be displayed for 10 sec.

End of Capacity Alert
The TOPARGEE H2Flow will give an audible alert and the digits blink on the LCD display when the remaining capacity reaches zero or minus.

Resetting
When the water tank has been refilled.  Press “DISPLAY” button to turn display on, then press the “RESET” button for five seconds, the “rESEt” on the LCD display blinks twice and the buzzer will sound, the unit will then be reset to the originally programmed value.  TIP!  You may find it easier to use the side of your fingernail or coin etc. to hold the button in for the five seconds.

Note: Due to continuous product improvement, specifications are subject to change without notice. 

Warranty 
1 year manufacturer warranty

To change from litres to gallons or gallons to litres:

  1. Disconnect the power (or batteries)
  2. Press and hold the “PROG” button while reconnecting the power.
  3. Release the button when you hear the long beep.  The display will be switched (from litres to gal, or gal to litres)
  4. Wait until the screen turns off and the unit will memorize the setting.​​

SKU: 13761 - Need Help? Contact Us Leave Feedback

Category: .

Call Now Button